Just bought 2 JBL GTO7001 700 Watt Mono Subwoofer Amplifiers, Looking for right Subwoofers.? - 10 in jbl car subwoofer
There are 700 RMS at 2 ohms and a couple of official statistics
http://jbl.com/car/products/product_detail.aspx?prod=GTO7001&Language=ENG&Country=US&Region=USA&cat=AMP&ser=GTS
Here you will find information on the Board of my Jeep.
http://www.mobiletoys.com/partners/jbl/pages/whatFits.aspx
I have some 15 "Kicker L5, the 750 W RMS and thought it would be almost nearly equal to the subcommittee in RMS, but I'm not sure what is the maximum amplifier power ...
I need a few suggestions. Here are my questions
1. What are the 2-subwoofer that will fit in the back of my Jeep and not FI BTL Caro More (200 to 250 $ / pc)
Question 1 certificate.
What kind of sub would be the best combination of SQ and SPL
2. What are your thoughts on JBL amp?
3. All suggestions, you can use the box that sounds good and fits into the back of the sub I want to .. I have enough for the 10 S EXT I have some knowledge of them.
4. Confusion with 2 ohms and 4 ohms deterioratedHead and a clarification of amplifiers and speakers and wiring work and ahh .... could help link.
5. I'm just a pleasure to win this refurbished amps and JBL guarantees shop on eBay for 71.50 and 73.15 / piece? Lol Resale Value:
214.99
http://www.sonicelectronix.com/item_12248_JBL+GTO7001.html?utm_source=froogle&utm_medium=organic&utm_campaign=froogle
I will give a lot of thumb with
Monday, February 1, 2010
10 In Jbl Car Subwoofer Just Bought 2 JBL GTO7001 700 Watt Mono Subwoofer Amplifiers, Looking For Right Subwoofers.?
1 comment:
First, the maximum performance is not so important because it means anything in car audio, everything that matters is the RMS (RMS) Power
1 a) any form of sub size.shape depends only on the box is not necessary (to be fit and still has the necessary internal volume ft.)
1b) the quality of your sound should come from the speakers inside, as long as you have the correct voltage and the field size / type of underwater sound quality will be OK
2) JBL amplifiers are CEA-compliance, which means that have been tested and produce or exceed their advertising Watts RMS with low distortion and the distortion is the main cause of speaker damage over time - Nice amps
3) the link does not work show jeep, so I do not know the dimensions http://www.diysubwoofers.org/faq.htm
4) From this link, you can sub in different contexts and to show you what the final impedance (ohms) amplifiers http://www.the12volt.com/caraudio/woofer changing ... the lower the impedance at the amplifier end of the low sound quality, but the easiest / least expensive is the power (I like 2Ohm finalImpedance configurations)
5) I am a little jealous of you
I went with 15 'cable 2 Ohms L5S also that http://www.the12volt.com/caraudio/woofer ...
If you sub too much power to your own, you run the risk of damage. The cone speaker and the mechanical parts, the passwords can make under stress break. Surprisingly, too little power can also damage your subwoofer - in fact, actually more frequently than the damage caused by the victory.
If the volume on the amp and did not have enough power, the signal is distorted or "cut". This distorted signal can be part of the speaker to overheat, warp and melt. Not good!
They have not exactly on the approximation of the speaker and amplifier power. An amplifier with increased output of the speaker characterization does not necessarily damage the speaker - just the amp back a little when you hear distortion in the subregion and run the speakers high volume for long periods. Similarly, all go well with a low-power amplifier if the volume remainsdown and not feed a distorted signal to the Sub-Committee
the amplifier is sent Clipping
Clipping
Clipping occurs when an amplifier is asked to give more power amplifier speaker is capable of. When an amplifier clips, literally cut off the top and bottom waveforms musical trying to replicate, hence the term. This leads to a huge distortion in the output signal. Clipping can be heard like a crack at musical peaks.
that distorted sound caused their boats in time loss
To maximize the power of the clean signal from your amplifier, you need to set the sensitivity of the gain or input parameters. Here's how:
Adjust the sensitivity of the input controls the power amplifier to its minimum level (counter-clockwise).
Must put in a CD and turn the volume control on your receiver (you may need to increase the amplification factor is only a little to hear the music).
If you hear distortion, stop. Turn down the volume until it disappears. As a sign of what is happening as possible to the receiver amplifier.This optimizes the signal-to-noise ratio, and makes the system less susceptible to problems with motor noise. Keep the volume setting here.
Turn on the amplifier gain control until it is as hard as you play. If you hear distortion, slightly decrease the gain setting.
Now that you're the one with the volume of the receiver optimized to the ceiling. You can adjust the volume almost all the way and does not damage your speakers or amplify distortion. If you have a subwoofer, a test disc (or bass-heavy CD combined) is beneficial for the final adjustments.
Post a Comment